Battery Charger Staudte Hirsch SH-3.130, 6 V/12 V, 4.5 A

Battery Charger Staudte Hirsch SH-3.130, 6 V/12 V, 4.5 A

Zoom image
Important characteristics and features:


• Suitable for 6 V and 12 V lead batteries (Acid, Gel, AGM)
• Suitable for 12 V lithium batteries with BMS

• Multi-step, microprocessor-controlled charging method
• Motorbike mode for 6 V/12 V lead batteries with lower capacity
• Regeneration step for reactivation of deep-discharged batteries
• Float charging phase and auto-memory-function
• Protection against short circuit, reverse polarity and overcharging
• Robust, jet-water-protected and dust-tight housing (IP 65)
• Easy operation
• Delivery including 2-piece charging adapter set


 

61,80 EUR

19 % VAT incl.

Product no.: 331300
EAN: 4030072331302

Battery Charger Staudte Hirsch SH-3.130, 6 V/12 V, 4.5 A
Battery Charger Staudte Hirsch SH-3.130, 6 V/12 V, 4.5 A
Battery Charger Staudte Hirsch SH-3.130, 6 V/12 V, 4.5 A
Battery Charger Staudte Hirsch SH-3.130, 6 V/12 V, 4.5 A
Battery Charger Staudte Hirsch SH-3.130, 6 V/12 V, 4.5 A

 

Recommended application:
 



 

      

  


Allround charger with special motorbike mode

The fully automatic Battery Charger SH-3.130 is suitable for charging and maintaining rechargeable 6 V and 12 V lead batteries as well as 12 V lithium batteries (LiFePO4) with integrated battery management system (BMS). Thus, it is very versatile in its application. In the 6 V resp. 12 V motorbike mode even small rechargeable batteries can be charged gently and with a lower charging current (max. 1 A).

Moreover, the Staudte Hirsch professional charger SH-3.130 offers several charging modes that are optimized for the special requirements of the respective battery types: the 12 V AGM mode for rechargeable batteries with a higher cut-off-voltage, the 12 V SLA/Gel mode for lead-acid or lead-gel batteries from 14 Ah and the 12 V lithium mode for LiFePO4 batteries with integrated battery management system.

With the intelligent charging method and the float charging phase, the battery voltage is constantly monitored and the battery optimally recharged when needed. This ensures that the battery is perfectly maintained and always ready for use. Batteries in seasonal vehicles that are used only sporadically should therefore generally remain connected to the charger.


Recommended application:
Car, transporter van, mobile home, tractor, ride-on-mower, quad bike, motorcycle, motor scooter, autocycle, snowmobile, jetski, motor boat, sailing boat and much more.


 

The most important characteristics and features:

 

 Advantages of the intelligent, multi-step charging                               


The fully automatic multi-step charging method guarantees that your battery is charged fully and gently in the shortest possible time and according to its type.

 
Mode          Battery type  Battery capacity  Charging current  Cut-off-voltage 
AGM 12 V AGM batteries from 14 Ah 4.5 A  14.7 V
SLA/Gel
  
12 V lead-acid batteries
12 V lead-gel batteries
from 14 Ah 4.5 A  14.4 V
Lithium 12 V LiFePO4 batteries with BMS from 25 Ah 4.5 A  14.4 V
6 V Motorbike        6 V lead batteries   < 14 Ah 1 A   7.2 V
12 V Motorbike 12 V lead batteries   < 14 Ah 1 A 14.4 V

 

 

 Regeneration step for the reactivation of deep-discharged batteries       


When a battery is connected to the charger, the device first determines independently what the charging status of the battery is (deep-discharged, partially discharged). If the battery is detected as deep-discharged, the charging process will automatically start in the regeneration mode. In this case, a lower charging current is used to bring the deep discharged battery back to a battery voltage at which the regular charging function can be started.

Should this be no longer possible, the battery is detected as defective and the error is indicated by an optical signal.
 

 

 Float charging phase – ideal for longer periods of inactivity       


Thanks to the float charging phase included in the multi-step charging process, the battery capacity is constantly monitored, optimally recharged if necessary and capacity losses due to self-discharge are compensated immediately.

This fully automatic feature will always guarantee the instant operability of your vehicle and ensure that your battery is fully efficient even after long periods of inactivity.

 

 

 Integrated: Auto-Memory-Function       


The auto-memory-function ensures that the battery charger returns automatically to the previously selected mode after power is restarted following a supply voltage failure.

 

 

 Safe operation – protection against short circuit, reverse polarity and overcharging 


Defective, short-circuited or reverse-poled rechargeable batteries are automatically detected by the charger and indicated by visual warning signals.

 

  

 Clear display – easy to use                              

 

 

       

Clear operation and display panel 

1  Charging mode indicators
2  6 V Motorbike mode                                    
3 
12 V Motorbike mode                                   
4 
Operating display                                    
5 
Connection cable with reverse polarity                                    
6 
Battery defective/short circuit of connection cable
7  Charging status indicators
8  Mode selection
 

 
 
 


The clearly arranged operation and display panel has charging mode, charging status and error indicators. It keeps you informed about the selected operating mode, the selected battery type and its charging status, at all times. Possible errors are visually displayed.

With the MODE button you can easily and conveniently make the desired settings or select the charging method.

 

 

 Robust, jet-water-protected and dust-tight housing (IP 65)                              

 

Its robust, jet-water-protected and dust-tight housing (IP 65) allows the charger to be used safely and reliably outdoors in rain or snow.

Thanks to its practical mounting rail, it can be firmly mounted, for example, on the garage wall.

      

 

 Included charging adapters – Conveniently connect and exchange                             

 

The 2-piece, water-protected (IP 44) adapter cable set,
which is included in the delivery content, allows for a versatile and flexible use:

           


Simply connect and exchange
Thanks to the quick-contact plug, the required
adapter cable can simply be connected to the
charger cable and, if necessary, replaced with
another one.

  

 

Adapter cable with battery clamps
By means of the completely isolated battery
clamps, the charger can be quickly and safely
connected to or disconnected from the battery.

 

        
 
    








 

           
Adapter cable with eyelet rings
It can be permanently connected to hard-to-reach
batteries.
Advantage: The eyelets only have to be fixed to
the battery once. After that, the charger can be
connected to e.g. the motorcycle with little effort
using the quick-contact plug. (Diameter eyelet
rings outside 12 mm, inside 6.5 mm).

 

 

   


The adapter cables may also be ordered separately:

 

3-piece adapter cable set

To the set >

 

Adapter cable with battery clamps

To the product >

  Adapter cable with eyelet rings   

To the product >

 
Adapter cable with 12 V plug

To the product >

 

   

 

 

 12 V AGM mode                              

 

 

Step 1: Softstart phase
The first charging step serves to put a deep discharged battery back into a chargeable state. The softstart phase is not necessary if the battery voltage is at least 10.0 V.

Step 2: Bulk phase
In this step, the battery is constantly charged with max. 4.5 A charging current.

Step 3: Absorption phase
In step 3, the battery is charged with constant voltage.

Step 4: Floating phase
After reaching the cut-off-voltage (14.7 V), the battery is constantly supplied with current.
Capacity losses through self-discharge are compensated immediately.

 

 

 12 V SLA/Gel mode                             

 

 

Step 1: Softstart phase
The first charging step serves to put a deep discharged battery back into a chargeable state. The softstart phase is not necessary if the battery voltage is at least 10.0 V.

Step 2: Bulk phase
In this step, the battery is constantly charged with max. 4.5 A charging current.

Step 3: Absorption phase

In step 3, the battery is charged with constant voltage.

Step 4: Floating phase
After reaching the cut-off-voltage (14.4 V), the battery is constantly supplied with current. Capacity losses through self-discharge are compensated immediately.

 

 

 12 V Lithium mode       

 

 

Step 1: Check phase
If the battery management system (BMS) is switched off due to low battery voltage, it is reactivated by a control signal from the battery charger. Not until then does the charging process start.

Step 2: Softstart phase
The softstart phase serves to put a deep discharged battery back into a chargeable state. This charging step is not necessary if the battery voltage is at least 10.0 V.

Step 3: Bulk phase
In this phase of the charging process, the battery is constantly charged with max. 4.5 A charging current.

Step 4: Absorption phase

In this charging step, the battery is charged with constant voltage.

Step 5: Floating phase
After reaching the cut-off-voltage (14.4 V), the battery is constantly supplied with current. Capacity losses through self-discharge are compensated immediately.

 

 

 6 V and 12 V Motorbike mode                             

 

The motorbike mode is suitable for charging small 6 V or 12 V batteries under 14 Ah.
The cut-off-voltage is 7.2 V (for 6 V batteries) or 14.4 V (for 12 V batteries) in the respective mode. The charging current is limited to 1.0 A.



6 V Motorbike mode – Charging curve and charging method

 


 

12 V Motorbike mode – Charging curve and charging method

 

 


Step 1: Softstart phase
The first charging step serves to put a deep discharged battery back into a chargeable state. The softstart phase is not necessary if the battery voltage is at least 5.0 V (6 V motorbike mode) or 10.0 V (12 V motorbike mode).

Step 2: Bulk phase
In this step, the battery is constantly charged with max. 1.0 A charging current.

Step 3: Absorption phase

In step 3, the battery is charged with constant voltage.

Step 4: Floating phase
After reaching the cut-off-voltage of 7.2 V (6 V motorbike mode) or 14.4 V (12 V motorbike mode), the battery is constantly supplied with current. Capacity losses through self-discharge are compensated immediately.

  

 

 3 year manufacturer warranty          

 

  Staudte Hirsch products are manufactured following a high quality standard and strict quality guidelines. We are so convinced of the longevity of our products that we add another year to the statutory manufacturer warranty free of charge.

 

 

 Delivery content             


• Battery Charger SH-3.130
• Adapter cable with battery clamps
• Adapter cable with eyelet rings
• Instruction manual in DE, GB

 



       

Technical data

    

Battery Charger SH-3.130, 6 V/12 V 4.5 A

 


Input

     
Operation voltage   100 – 240 V AC, 50/60 Hz  
Input current   max. 1.4 A  
Power consumption   75 VA  

Output
     
Suitable battery voltage   6 V/12 V  
Charging current  

max. 1.0 A ± 10 % motorbike mode
max. 4.5 A ± 10 % lead and lithium mode

 
Rechargeable battery type   6 V and 12 V lead batteries (Acid, Gel, AGM)
12 V LiFePO4 batteries
 
Battery capacity   from   1.2 Ah motorbike mode
from 14.0 Ah lead mode
from 25.0 Ah lithium mode
 
Charging method   multi-step  
Cut-off-voltage   6 V battery:
7.2 V ± 0.2 V
12 V battery:
14.4 V ± 0.2 V SLA/Gel and motorbike mode
14.4 V ± 0.2 V lithium mode
14.7 V ± 0.2 V AGM mode
 

General
     
Reverse current   < 0.5 mA  
Protection type
 
  IP 65 (charger)
IP 44 (adapter cable set)
 
Cable length
 
  1.70 m (mains cable)
1.60 m (connection cable incl. adapter)
 
Dimensions   203 x 48 x 67 mm  
Weight   490 g (without accessories)
610 g (with accessories)
 
       

 

Downloads:

 


 


 


 


 

Data sheet Battery Charger SH-3.130,
6 V/12 V, 4.5 A

 

Instruction manual Battery Charger SH-3.130, 6 V/12 V, 4.5 A
 

Charging characteristics Battery Charger SH-3.130, 6 V/12 V, 4.5 A
 

Dimensioning
 


 

 

Download PDF Version » Download PDF Version » Download PDF Version » Download PDF Version »
       

 

 

 

 

Recommended products:

3-piece charging adapter set

3-piece charging adapter set


• Simple connection with quick-contact plug
• Water-protected (IP 44) 
• Consists of:
  Adapter cable with battery clamps 
  Adapter cable with 12 V plug
  Adapter cable with eyelet rings 
• Suitable for Staudte Hirsch Battery Chargers
  SH-3.130 and SH-3.150
• Suitable for IVT chargers
  PL-C010P, PL-C004P and PL-782B 

 

Art.Nr.: 911000.A

17,95 EUR (19 % VAT incl.)

Adapter cable with battery clamps

Adapter cable with battery clamps


• Simple connection with quick-contact plug
• water-protected (IP 44) 
• Suitable for Staudte Hirsch Battery Chargers
  SH-3.130 and SH-3.150
• Suitable for IVT chargers
  PL-C010P, PL-C004P and PL-782B 

 

 

Art.Nr.: 911000.K

7,95 EUR (19 % VAT incl.)

Adapter cable with eyelet rings

Adapter cable with eyelet rings


• Simple connection with quick-contact plug
• water-protected (IP 44) 

• Suitable for Staudte Hirsch Battery Chargers
  SH-3.130 and SH-3.150
• Suitable for IVT chargers
  PL-C010P, PL-C004P and PL-782B 

 

 

Art.Nr.: 911000.O

4,59 EUR (19 % VAT incl.)

Adapter cable with 12 V car plug

Adapter cable with 12 V car plug


• Simple connection with quick-contact plug
• Water-protected (IP 44) 

• Suitable for Staudte Hirsch Battery Chargers
  SH-3.130 and SH-3.150
• Suitable for IVT chargers
  PL-C010P, PL-C004P and PL-782B 


 

Art.Nr.: 911000.Z

7,95 EUR (19 % VAT incl.)

Zur Kenntnis genommen

Diese Webseite verwendet Cookies. Durch den Besuch dieser Webseite stimmen Sie der Nutzung von Cookies zu. Mehr erfahren